≡

ELISA Kit for Leukotriene C4 (LTC4)

LT-C4

Specificity

This assay has high sensitivity and excellent specificity for detection of Leukotriene C4 (LTC4).
No significant cross-reactivity or interference between Leukotriene C4 (LTC4) and analogues was observed.

Recovery

Matrices listed below were spiked with certain level of Leukotriene C4 (LTC4) and the recovery rates were calculated by comparing the measured value to the expected amount of Leukotriene C4 (LTC4) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 85-101 89
EDTA plasma(n=5) 85-99 96
heparin plasma(n=5) 91-104 97

Precision

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Leukotriene C4 (LTC4) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Leukotriene C4 (LTC4) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Leukotriene C4 (LTC4) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 95-103% 79-101% 78-88% 82-92%
EDTA plasma(n=5) 79-95% 80-90% 80-93% 93-101%
heparin plasma(n=5) 80-96% 98-105% 95-102% 94-102%

Stability

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Reagents and materials provided

Reagents Quantity Reagents Quantity
Pre-coated, ready to use 96-well strip plate 1 Plate sealer for 96 wells 4
Standard 2 Standard Diluent 1×20mL
Detection Reagent A 1×120µL Assay Diluent A 1×12mL
Detection Reagent B 1×120µL Assay Diluent B 1×12mL
TMB Substrate 1×9mL Stop Solution 1×6mL
Wash Buffer (30 × concentrate) 1×20mL Instruction manual 1

Assay procedure summary

1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
    And then add 50µL prepared Detection Reagent A immediately.
    Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
7. Add 50µL Stop Solution. Read at 450 nm immediately.

GIVEAWAYS

INCREMENT SERVICES

Magazine Citations
Toxicology and aApplied Pharmacology_ 5-lipoxygenase activation is involved in the mechanisms of chronic hepatic injury in a rat model of chronic aluminum overload exposure pubmed:27368151
Catalog No. Related products for research use of Pan-species (General) Organism species Applications (RESEARCH USE ONLY!)
CEA619Ge ELISA Kit for Leukotriene C4 (LTC4) Enzyme-linked immunosorbent assay for Antigen Detection.
CCA619Ge CLIA Kit for Leukotriene C4 (LTC4) Chemiluminescent immunoassay for Antigen Detection.
LMA619Ge Multiplex Assay Kit for Leukotriene C4 (LTC4) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.