≡

CLIA Kit for Platelet Derived Growth Factor AB (PDGFAB)

PDGF-AB

Specificity

This assay has high sensitivity and excellent specificity for detection of Platelet Derived Growth Factor AB (PDGFAB).
No significant cross-reactivity or interference between Platelet Derived Growth Factor AB (PDGFAB) and analogues was observed.

Recovery

Matrices listed below were spiked with certain level of recombinant Platelet Derived Growth Factor AB (PDGFAB) and the recovery rates were calculated by comparing the measured value to the expected amount of Platelet Derived Growth Factor AB (PDGFAB) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 88-98 91
EDTA plasma(n=5) 80-104 97
heparin plasma(n=5) 89-102 96

Precision

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Platelet Derived Growth Factor AB (PDGFAB) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Platelet Derived Growth Factor AB (PDGFAB) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Platelet Derived Growth Factor AB (PDGFAB) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 98-105% 78-99% 90-104% 81-94%
EDTA plasma(n=5) 91-99% 79-105% 80-94% 87-101%
heparin plasma(n=5) 83-92% 97-105% 82-90% 94-105%

Stability

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Reagents and materials provided

Reagents Quantity Reagents Quantity
Pre-coated, ready to use 96-well strip plate 1 Plate sealer for 96 wells 4
Standard 2 Standard Diluent 1×20mL
Detection Reagent A 1×120µL Assay Diluent A 1×12mL
Detection Reagent B 1×120µL Assay Diluent B 1×12mL
Substrate A 1×10mL Substrate B 1×2mL
Wash Buffer (30 × concentrate) 1×20mL Instruction manual 1

Assay procedure summary

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

GIVEAWAYS

INCREMENT SERVICES

Magazine Citations
PeerJ Platelet-rich concentrate in serum free medium enhances osteogenic differentiation of bone marrow-derived human mesenchymal stromal cells pubmed:27651984
Materials Science & Engineering C-Materials for Biological Applications Effect of crystalline phase changes in titania (TiO2) nanotube coatings on platelet adhesion and activation Pubmed:29025678
EXPERIMENTAL GERONTOLOGY The application of thermal oscillation method to augment the effectiveness of autologous platelet rich plasma in treating elderly patients with knee osteoarthritis Pubmed: 33091524
Catalog No. Related products for research use of Homo sapiens (Human) Organism species Applications (RESEARCH USE ONLY!)
SEA436Hu ELISA Kit for Platelet Derived Growth Factor AB (PDGFAB) Enzyme-linked immunosorbent assay for Antigen Detection.
SCA436Hu CLIA Kit for Platelet Derived Growth Factor AB (PDGFAB) Chemiluminescent immunoassay for Antigen Detection.
LMA436Hu Multiplex Assay Kit for Platelet Derived Growth Factor AB (PDGFAB) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.